Edit this page
Update of Ford Tibbe InstructionsUpdate of Ford Tibbe Instructions The ford Tibbe lock is a rotary disc mechanism.  All of the discs need to be rotated to a correct position before the side bar can locate into the true gates allowing the lock to open.

There have been two designs of disc that have had distinct similarities. In both designs there has always been one true gate and two false gates. In the first ,early, design the false gates were shallow gates that imitated the true gates. In the second and current design the false gates are notches cut into the disc. The notches are wide enough to allow the side bar to catch into them when picking.


The Tibbe pick comes with a central wire that runs through the tool. This wire is required to achieve tension in order to pick the early locks. Tension is achieved by putting the wire to the back of the lock and into the drain hole at the locks base. The torque tube is then locked into place as it captures the wire.

The wire is not required for newer locks as the bottom of the lock is shaped the same as the tip of the pick.

Recommended picking procedure is as follows. Prior to inserting the tool use a blank key to align all of the discs. The tool will now easily enter the lock and seat at the bottom. Push the pick to the bottom of the lock and apply light tension in the opening direction. The opening direction is opposite to the spring pressure that can be felt. Now pick every disc into a gate. At this point it does not matter if it is a true gate or false gate, what we are trying to do is lower the side bar into the pack of discs so that the lock becomes more responsive. Some clicking and movement of the tension handle may be felt. When picking the discs it can be helpful to position each one at its start position and then pick it towards the opening direction. A number 4 disc will have no movement and there may well be more than one number 4 disc, but there will always be at least one.

Once all discs are in a gate test each one individually to try to determine its true gate position. Each one can be moved through its range of movement back and fourth until you find the gate. The true gate will either indicate with more pick movement when in that position or as the disc aligns to that true position movement in the opening direction will be felt in the tension handle.
When all discs are positioned correctly the lock will open.

When the lock is in the open position it can be decoded from the pick.
The procedure for decoding is as follows. Hold the lock in the open position and place the pick on a known number 4 disc. Undo the brass terminal screw on the
collet and position the line at one end in alignment with the long line on the graduated scale. Your number 4 disc is now indicating 4 against the 4th collet line against the graduated scale. Now read all other discs against the remaining 3 lines on the collet.

A better understanding of how this lock works can be gained by watching the animation and explanation on the Ford Tibbe Pick page in Automotive Tools.


More articles

Drill Rig
Drill Rig Introducing the latest version of the magnetic safe drilling system which has been refined over the last 15 years. This new design allows the drill and slide to be removed to give full access to the hole for punch and drill techniques and for visual inspection.This latest design also incorporates a much more compact slide bracket assembly. The slide assembly is fully adjustable for wear and can be easily adjusted according to the user’s preference. The new switching unit on the side of the stand can be used to control the drill motor meaning only one power lead is required for drill and stand.The stand is available in 110V or 240V and comes in a larger blow moulded case complete with adjustment tools, cutting oil and oil bottle. Any 43mm pistol drill can be used, however it is optimised for use with the Festool PD 20/4 E. Combined with the Festool Drill motor, the stand can be used in confined spaces where there is limited room between the safe and other obstructions for example... read more
New news
New news Coming Soon... read more
NEW Fichet Pick/Decoder
NEW Fichet Pick/Decoder Prototype has been proven to work very well on M2i, M2b and the M3 series. These tools will be available to purchase by the end of September...reserve yours now.... read more
New news
New news SAFE VENTURES HAS MOVED.As of Feb 2016 Safe Ventures has moved to:53 Pengrove RoadHerefordHR1 1BT... read more
European Lock Federation in Dublin
European Lock Federation in Dublin Safe Ventures will be attending the ELF show in Dublin this coming 23rd/24th May.... read more
Mauer Code Combi B + B30 SCYTHE Tool
Mauer Code Combi B + B30 SCYTHE Tool The Scythe tool for the Mauer Code Combi B and Code Combi B30 electronic lock uses the bypass keyway to great effect.These locks are opened very easily within seconds.Comes with instructional media including video.... read more
SEMS training stand
SEMS training stand I have a batch being manufactured and due for delivery soon.Lock not included, base may be different material.... read more
Impression Kit
Impression Kit Available with No.4 impression file, light box, impression handle,and other bits and pieces.... read more
E-LOCK BATTERY ANALYZER from Taylor Technologies, available now look in the tools section for full description.... read more
New news
New news from Taylor Technologies, available now... read more
Now available
Now available Impression Light on the Tools page.... read more
Pin & Cams
Pin & Cams An engineering re think has been taking place with regards to the Pin & Cam system. The theory itself is good but we have been running through different application to find more lift and more reliability. So far we have a 6K174 P&C which gives us a reliable 0.8mm lift.  Before while achieving this amount of lift, came the potential for the tool to jam,  this problem has been solved.We now have a number of 110, 114 and Legge P&C\'s arriving, all of which have had the redesign applied.  ... read more
Video Scope
Video Scope Available from Safe Ventures. This video scope is switchable between Zero and 90 degree and comes with an integral 3.5 inch screen ... read more
TSM Safe Manipulation Assistant
TSM Safe Manipulation Assistant The successor to the CB Assistant which is no longer manufactured. This tool\'assists\'with the logging of contact points during dial safe lock manipulation. The Manipulator uses the computer generated information to interpret where the wheels gates are located. Also used in Manipulation instruction to help student understand how the lock function.... read more
Technical Entry Curtain Pick
Technical Entry Curtain Pick Another addition via Technical Entry, their curtain lock pick system, ( TE Multi-Pass) we believe is the best curtain lock pick tool available in the world today... read more
S2, S5 and CT12 Make up Keys
S2, S5 and CT12 Make up Keys Newly engineered and available to order.... read more
Chubb 2M22 Pick
Chubb 2M22 Pick This lock has been widely used by Chubb for internal safe cupboards and drawers and also for securing the back pans to its strong room doors.This 6 lever lock used a flat key and incorporates rotating nozzle to hold the key and make manipulation more difficult. While the lock can be forced open it is relatively straight forward to pick open with a little practice and can then be easily be rekeyed.The pick lifts all levers to the bottom lift height to aid the picking process.... read more
NEW PIN & LIFT TOOLS We now have the pin and lift tools for Chubb 3G114, 3G110 and Legge curtained lever locks.For the past 20 years we have used pin and cam technology against these locks whilst using the far more sensitive pin and lift technology against high security safe locks. The systems are very similar in their application but pin and lift is a more successful and user friendly approach to the problem.The main reason for change is defeat of the Chubb 110. This is an extremely good quality lock with over 23000 key code possibilities.Over the years myself and others have struggled on this lock due to lack of feel and what is known as lever slip.I have recently tested pin and lift against the problem and started to supply a few customers on a trial basis. Below is some feedback that has influenced the decision to make change.\" I would like to give you some feedback having used the new Chubb 110 pin and cam, or as I refer to it, pin and plunge. I\'ve been using it for a couple of weeks and in that tim... read more
Basic Safe Opening Course
Basic Safe Opening Course Dates for future courses in 2014 will be announced soon Martin Newton Basic Safe TrainingLIMITED to 4 PLACES Safe & vault opening is a vast subject, Martin\'s personal knowledge and database has developed over a twenty year period and he is still learning.Our approach to this subject is to divide it into sub categories. The criteria for doing this is popularity of container and degree of difficulty to open. The majority of safes manufactured and purchased  can be described as containers with a cash value of less than £10,000.00. This cash value is allocated by the Association of British Insurance Surveyors.Our Basic Safe Opening course centers around safes that are 10k rated and less. This includes Hotel Safes, Domestic Safes, light commercial safes floor safes and wall safes.By definition these containers are usually constructed to a fairly decent physical standard and are often secured in position i.e., bolted to the floor or wall.  Open access can be secured by m... read more
Certified Professional Safe Technician
Certified Professional Safe Technician I recently tested for this qualification whilst on some training courses in America.The exam was 357 questions on 11 categories in 4 hours.I had to guess the last 20 questions as I ran out of time but put all the answers as B.Got the results today and delighted to have passed.RegardsMartin CPS... read more
Congratulations Ron Snively
Congratulations Ron Snively Below is an article concerning my good friend and former S.A.V.T.A. president Ron Snively. A very professional job, well done Ron.Police in Conyers, GA, near Atlanta, are investigatisng a case of a toddler who walked into a bank vault on Friday, just as the timers activated, locking the little girl inside the bank vault. A technician was rushed to the bank, escorted by the police at a 90-mile-per-hour clip, to drill out the lock and rescue the child.Apparently, the little girl and her mother were visiting the child’s grandmother, who is an employee at the Wells Fargo branch at GA Highway 138 and GA Highway 20, where the incident occurred. Deputy Chief Mike Lee of the Rockdale County Fire Department indicated that the little girl was freed from the vault at approximately 9 p.m., after three hours inside, “crying a little bit, but doing well,” reported television station 11Alive in Atlanta.The incident occurred after the bank had actually closed, and customers had left the bank. At... read more
A blast from the past !
A blast from the past ! I was clearing out some old papers and came across this from 1994. I remember the real problem was JF and I not agreeing our strategy before hand, he was decoding top to bottom, I was recording bottom to top, so for about twenty minutes we had the code but were trying to apply it in reverse. You live and learn I guess!... read more
A few words on combination lock manipulation by Mark Bates
A few words on combination lock manipulation by Mark Bates During the past five years I have had the good fortune to spend time opening safes with a close friend from across the Atlantic, Mark Bates. Mark is the owner of MBA USA Inc, a locksmith and safe technician tool supply and training company. During visits to the U.K. I have witnessed Mark manipulate several combination locks. The time taken has varied from30 minutes to 5 hours and there was only one occasion that Mark was defeated by the lock. All of the above has led to many conversations regarding, what I would describe, as the subtleties of manipulation. It has been during these discussions that I have come to realise that Mark Bates knows a LOT about manipulation.I have asked him to try and explain  a little of that knowledge here. MARKS RESPONSEI have been asked to say a few words about combination lock manipulation. This is more difficult than might be imagined, as manipulation is the act of doing…of being fully absorbed in the present. It is not a thing that can be easily ... read more
So you want to get into safes. By Martin Newton
So you want to get into safes. By Martin Newton I am constantly faced with enquiries from people wanting to start up in the safe trade, so I thought I would write this article to give an insight as to what is involved. About 10 days ago I had a call on my mobile phone, the caller asked if it were me by name and said he had been given my number by a mutual friend. He then said that he was standing in front of a ministry safe fitted with a MkIV Manifoil combination lock that would not open. For those that don’t know this job would fall into the category of high security. He wondered if I could give him a drill point. After asking a couple of questions I extracted from him that he had changed the combination on the lock less than 2 weeks ago and now it was not opening. The identity of the caller is still unknown to me, my advice to him, was to walk away from it and to advise the customer to call a professional safe engineer.This article is aimed at being informative and educational to those who are considering getting into safes in s... read more
Chubb 3G110
Chubb 3G110 A big thank you goes out to Simon Owen for providing this informative guide on understanding the Chubb 3G110. I have known Simon a long time and he understands this lock as well as anyone I know. Hopefully this information will help those who are experiencing problems in opening the lock.This guide has been written to enable users of the Safeventures 110 pin and cam system to better understand a technique for opening these locks.The technique relies on you identifying the difference between pattern 2 and pattern 3 detainers, once identified it is much easier to find a true gate.Often too much rotational force results in ‘false binds’ which cause false pin moves which will result in the lock not opening. Fractional movement of the cam is all that is requiredIf you follow the process of identifying the lever pattern first and sticking rigidly to this system Chubb 110 lock opening should become much easier.A detailed knowledge of the working parts of a lock enables you to understand b... read more
The evolution of S.E.M.S
The evolution of S.E.M.S The Spindle Extraction Manipulation System. The idea of trying to defeat a combination lock through the spindle hole is not a new one. HPC have been marketing spindle hole defeat tools for over twenty years. Whilst difficult to use I suspect, due to their relative cheap cost, that most professional safe tech’s have a set just for the sake of ‘you never know when they may come in handy’. Many of you will of heard me say this before. John Falle of Falle Safe Securities, Jersey, Channel Islands U.K. is a genius. He has a proven track record of innovative design for nondestructive lock opening tools that is unparalleled in our industry. About 15 years ago John and I, had a discussion regarding the merits of a tool that would open a combination lock through the existing spindle hole in a safe container. At that time John felt sure he could design a tool that would achieve this in a simple and efficient manner. Over the years our business relation ship has  cente... read more